TM-Electrical Engineer(Global)-Shenzhen
EngineeringElectrical Engineer
5 views0 saves0 applied
Quick Summary
Key Responsibilities
VFD, controller, EEV driver, current/voltage/temperature/pressure sensors, contactors, circuit breakers, relays and power supplies; conduct component selection,
Technical Tools
EngineeringElectrical Engineer
Key Responsibilities
- Lead electrical hardware design of DX cooling units, including power distribution circuit, compressor/EEV/fan drive control, sensor sampling, protection circuit, wiring diagram, terminal definition and cabinet layout.
- Define BOM for electrical components: VFD, controller, EEV driver, current/voltage/temperature/pressure sensors, contactors, circuit breakers, relays and power supplies; conduct component selection, evaluation and single-source risk management.
- Develop electrical schematics, wiring drawings, panel layout, cable routing specification and test procedure; manage drawing release, revision and technical document control.
- Conduct EMC, electrical safety and reliability assessment; organize related verification tests (surge, ESD, conducted/radiated emission, insulation, withstand voltage, over-current/over-temperature protection).
- Support control logic integration with thermal system: compressor capacity regulation, EEV superheat control, fan speed modulation, alarm interlock, fault diagnosis and protection logic matching for DX refrigeration cycle.
- Drive DFM review for electrical design, work with manufacturing and supply chain to optimize wiring harness, panel assembly and testability; support cost optimization of electrical bill of material.
- Support prototype, pilot run and mass production ramp-up; troubleshoot electrical and control issues including communication failure, sensor drift, drive abnormal trip, protection misfire and wiring interference during NPI and volume production.
- Resolve field quality escalations related to electrical hardware, drive faults, signal noise and protection failures; conduct root cause analysis and roll out corrective & preventive actions.
- Track relevant industry standards, safety certifications and new electrical components for cooling equipment; complete benchmarking and technical pre-research for next-gen DX control platforms.
- Align with thermal, mechanical and product teams to translate product requirements into electrical design, balancing safety, reliability, performance, cost and serviceability.
- Bachelor’s degree or above in Electrical Engineering, Automation, Control Science & Engineering, Refrigeration & HVAC or related discipline.
- 3+ years electrical hardware design experience for HVAC / refrigeration equipment; solid experience in refrigeration unit power and control circuit design.
- Proficient in E-CAD tools (EPLAN preferred); familiar with electrical drawing standards, low-voltage distribution, wiring harness design and component specification.
- Hands-on experience with EMC and electrical safety test requirements; understand common protection mechanisms for compressor, EEV and fan drive systems.
- Basic understanding of DX refrigeration cycle, superheat control and typical operating faults of direct expansion cooling systems.
- Familiar with reliability test methodology for cooling products; able to conduct electrical fault analysis and design improvement.
- Strong systematic thinking, good cross-team communication; capable of managing multiple tasks under tight NPI schedules.
- Good English reading and writing skills for technical documents and global cross-team communication.
- Experience on data center mission-critical cooling products (DX CRAC, in-row cooler)
- Familiar with Modbus / BACnet communication and building management system integration
- Practical experience with variable frequency drive commissioning and EEV control tuning
- Experience supporting NPI from concept to mass production
- Knowledge of IEC, UL and other global electrical safety standards for cooling equipment
Location & Eligibility
Where is the job
Shenzhen-Xili, China
On-site at the office
Who can apply
CN
About this job
- Who can apply
- China
- Posted
- 26 days ago
Listing Details
- Posted
- October 26, 2026
- First seen
- October 26, 2026
- Last seen
- November 20, 2026
Posting Health
- Days active
- 25
- Repost count
- 0
- Trust Level
- 19%
- Scored at
- November 21, 2026
Signal breakdown
freshnesssource trustcontent trustemployer trust
External application
Similar Electrical Engineer jobs
View all →Intern – Electrical Engineer – San Diego, CA – Summer 2027
$29.00 to $32.00
Senior Electrical Engineer
$137,196 — $205,382 USD
Principal Electrical Engineer
Intern - Electrical Engineer, RF Heating Systems - Spring 2027
USD 25–38 per hour
Internship
Electrical Engineer
Normal
Intern - Electrical Engineer - Spring 2027
USD 25–38 per hour
Internship
Browse Similar Jobs
Devops Engineer6.3kEngineering Manager4.5kFullstack Developer4kQa Engineer4kMechanical Engineer3.4kSoftware Architect3.1kProject Engineer2.9kDesign Engineer2.8kSecurity2.8kSecurity Engineer2.6kQuality Engineer2.5kBackend Developer2.2kProcess Engineer2kFrontend Developer1.6kApplication Engineer1.4kProduct Engineer1.3kAutomation Engineer1.2kEmbedded Engineer1.1kCivil Engineer1kMobile Developer999
Newsletter
Stay ahead of the market
Get the latest job openings, salary trends, and hiring insights delivered to your inbox every week.
A
B
C
D
No spam. Unsubscribe at any time.